Open the arms outward for wide crossover-style cable spacing, or converge them inward for a central 1:1 dual-stack route. Horizontal width and vertical height lock independently once set.
Open outward
Create Crossover-Width Cable Spacing
Sweep the arms left and right to open the pulley positions outward for wider cable paths and crossover-style training angles. Each extended arm adds 34cm of width on its own side of the rack.
Converge inward
Use Both Stacks in 1:1
Swing both arms inward to create a central 1:1 dual-stack route for low rows and lat pulldowns, making twice the single-stack capacity available through one attachment path.
75mmUpright compatibility
17mmHole compatibility
Designed as an upgrade path
Choose the Correct Extender Setup for Your Rack
+EXTENDER COMPATIBLE
B: Extender Arm only
Use the four-bolt swap-over interface. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A new cable is required for most existing conversions, unless a suitable spare cable can be adjusted.
CHECK COMPATIBILITY BEFORE ORDERING: This attachment has different component and cable requirements depending on the host rack. Review the Detailed Description before ordering. If you are unsure, contact RPM with your rack model and current cable setup so the correct configuration can be confirmed.
RPM Power Designed Pulley Extender Arm Attachment
Set Cable Height, Width and Direction Around the Station
After installation, use the vertical adjuster to raise or lower the arm and the horizontal adjuster to sweep through 180 degrees, opening outward for crossover-width spacing or converging inward for central cable paths. Horizontal width and vertical height lock independently once set. Each pulley rotates through 360 degrees to follow the selected line.
3Horizontal arm adjustment, independently lockable
360°Pulley rotation follows the cable line
Two cable modes in one system
Converge the Arms, Use Both Stacks in 1:1
Angle both arms inward to create a central 1:1 dual-stack route, doubling the available single-stack capacity for low rows and lat pulldowns.
STANDARD 2:1
Independent Cable Paths
On a compatible host cable system, use each arm independently with a single stack assigned to its chosen cable path.
CONVERGED 1:1
Central Dual-Stack Path
Bring both stacks together for rows, pulldowns and other central high-capacity cable movements.
Installation setting plus three live adjustments: Set the mounting-hole position once during installation to match the rack cable route. Thereafter, adjust vertical height, horizontal cable width and pulley rotation for the required training position.
Multi-position mounting
Designed for RPM’s Known Overhanging Pulley Paths
Developed in house by RPM Power for known RPM cable-path layouts, this is an installation setting rather than a training-time adjustment. Select the fixing position once around the overhanging pulley route used by the rack configuration so the arm and pulley sit in the intended cable line.
Multiple fixing positions: position the arm for the overhanging pulley route used by the rack.
ODIN rack path
Right and Left Upright-Side Top Pulleys
ODIN uses top-pulley paths to the right and left of the uprights. The fixing positions let the arm be placed to match those side cable routes.
Apex rack path
Central Upright Cable Path
Apex uses a central upright cable route. The arm can be fixed in the position that aligns with this central overhanging pulley placement.
Designed for every rack generation
A Clear Upgrade Path for Existing and Future Racks
The extender system is designed so both existing and future RPM rack owners can upgrade. Extender Compatible racks use a direct four-bolt swap-over route. Existing and non-compatible racks can also upgrade, but may require additional hardware and cable depending on the configuration already in place.
Component key: A is the upright dolly. B is the extender arm.
+EXTENDER COMPATIBLE
B: Extender Arm only
Remove the four bolts from the standard pulley dolly and attach the B extender arm in the same mounting position. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A cable change is required for most existing conversions. A suitable spare cable may be adjusted instead. The total upgrade cost therefore depends on the hardware and cable already in place.
+View cable and upright-dolly requirements
Existing standard-dolly installations require a cable change when converting to extender arms. Order a new cable alongside the arms where required. We can cut and supply the cable to the required length. Older stock and non-RPM rack conversions also require the A upright dolly.
From Q3 2026, new RPM 75mm x 75mm racks marked Extender Compatible will be supplied with sufficient cable for the standard pulley dolly or B extender arm when the selected configuration is specified at purchase.
Selection
Extender Arm Only, Upright Dolly + Extender Arm
Specifications
Specification
Details
Product
RPM Power Extender Arms
Arm Length
637mm
Arm Width
227mm
Net Weight
21kg
Gross Weight
25kg
Package A
34 × 22 × 25cm
Package B
50 × 31 × 24cm
Training Style
Strength, Hypertrophy, Functional & Athletic Training
The daily cut-off times for orders dispatched from RPM Power is 12pm. We aim to dispatch orders within the time frames outlined on ourShipping & Deliveries page. All times are measured in business days only and exclude weekends and Republic of Ireland public holidays.
Dispatch and delivery timeframes should be considered as estimates and are not guaranteed. These can vary during peak seasons and end-of-sale periods. We will draw your attention to any dispatch delays that may be occurring during these periods with a notice on our website.
Parcel orders: Small/lightweight items are dispatched via the courier network and automated tracking details will be provided to you. To ensure minimal shipping costs for our customers, some items may arrive in multiple packages. Although dispatched together, these packages can often become separated on their way to you and some may arrive a day later than the others.
Pallet orders: Heavy/oversized items are dispatched via the pallet network. Please note that there is no tracking reference provided for pallet deliveries and they are kerbside delivery service only meaning that the delivery driver will not bring your item(s) inside your home. Read our article on pallet deliveriesfor more information.
At RPM Power, customer satisfaction is our highest priority. We are committed to supporting you with any product-related concerns that may arise. While it is inevitable that issues may occasionally occur, our warranty policy is designed with a customer-focused approach to ensure a fair and efficient resolution.
All RPM Power products are covered under warranty. Warranty coverage varies depending on product type. For full details, please read our Warranties Terms and Conditions.
Open the arms outward for wide crossover-style cable spacing, or converge them inward for a central 1:1 dual-stack route. Horizontal width and vertical height lock independently once set.
Open outward
Create Crossover-Width Cable Spacing
Sweep the arms left and right to open the pulley positions outward for wider cable paths and crossover-style training angles. Each extended arm adds 34cm of width on its own side of the rack.
Converge inward
Use Both Stacks in 1:1
Swing both arms inward to create a central 1:1 dual-stack route for low rows and lat pulldowns, making twice the single-stack capacity available through one attachment path.
75mmUpright compatibility
17mmHole compatibility
Designed as an upgrade path
Choose the Correct Extender Setup for Your Rack
+EXTENDER COMPATIBLE
B: Extender Arm only
Use the four-bolt swap-over interface. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A new cable is required for most existing conversions, unless a suitable spare cable can be adjusted.
CHECK COMPATIBILITY BEFORE ORDERING: This attachment has different component and cable requirements depending on the host rack. Review the Detailed Description before ordering. If you are unsure, contact RPM with your rack model and current cable setup so the correct configuration can be confirmed.
Set Cable Height, Width and Direction Around the Station
After installation, use the vertical adjuster to raise or lower the arm and the horizontal adjuster to sweep through 180 degrees, opening outward for crossover-width spacing or converging inward for central cable paths. Horizontal width and vertical height lock independently once set. Each pulley rotates through 360 degrees to follow the selected line.
3Horizontal arm adjustment, independently lockable
360°Pulley rotation follows the cable line
Two cable modes in one system
Converge the Arms, Use Both Stacks in 1:1
Angle both arms inward to create a central 1:1 dual-stack route, doubling the available single-stack capacity for low rows and lat pulldowns.
STANDARD 2:1
Independent Cable Paths
On a compatible host cable system, use each arm independently with a single stack assigned to its chosen cable path.
CONVERGED 1:1
Central Dual-Stack Path
Bring both stacks together for rows, pulldowns and other central high-capacity cable movements.
Installation setting plus three live adjustments: Set the mounting-hole position once during installation to match the rack cable route. Thereafter, adjust vertical height, horizontal cable width and pulley rotation for the required training position.
Multi-position mounting
Designed for RPM’s Known Overhanging Pulley Paths
Developed in house by RPM Power for known RPM cable-path layouts, this is an installation setting rather than a training-time adjustment. Select the fixing position once around the overhanging pulley route used by the rack configuration so the arm and pulley sit in the intended cable line.
Multiple fixing positions: position the arm for the overhanging pulley route used by the rack.
ODIN rack path
Right and Left Upright-Side Top Pulleys
ODIN uses top-pulley paths to the right and left of the uprights. The fixing positions let the arm be placed to match those side cable routes.
Apex rack path
Central Upright Cable Path
Apex uses a central upright cable route. The arm can be fixed in the position that aligns with this central overhanging pulley placement.
Designed for every rack generation
A Clear Upgrade Path for Existing and Future Racks
The extender system is designed so both existing and future RPM rack owners can upgrade. Extender Compatible racks use a direct four-bolt swap-over route. Existing and non-compatible racks can also upgrade, but may require additional hardware and cable depending on the configuration already in place.
Component key: A is the upright dolly. B is the extender arm.
+EXTENDER COMPATIBLE
B: Extender Arm only
Remove the four bolts from the standard pulley dolly and attach the B extender arm in the same mounting position. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A cable change is required for most existing conversions. A suitable spare cable may be adjusted instead. The total upgrade cost therefore depends on the hardware and cable already in place.
+View cable and upright-dolly requirements
Existing standard-dolly installations require a cable change when converting to extender arms. Order a new cable alongside the arms where required. We can cut and supply the cable to the required length. Older stock and non-RPM rack conversions also require the A upright dolly.
From Q3 2026, new RPM 75mm x 75mm racks marked Extender Compatible will be supplied with sufficient cable for the standard pulley dolly or B extender arm when the selected configuration is specified at purchase.
The daily cut-off times for orders dispatched from RPM Power is 12pm. We aim to dispatch orders within the time frames outlined on ourShipping & Deliveries page. All times are measured in business days only and exclude weekends and Republic of Ireland public holidays.
Dispatch and delivery timeframes should be considered as estimates and are not guaranteed. These can vary during peak seasons and end-of-sale periods. We will draw your attention to any dispatch delays that may be occurring during these periods with a notice on our website.
Parcel orders: Small/lightweight items are dispatched via the courier network and automated tracking details will be provided to you. To ensure minimal shipping costs for our customers, some items may arrive in multiple packages. Although dispatched together, these packages can often become separated on their way to you and some may arrive a day later than the others.
Pallet orders: Heavy/oversized items are dispatched via the pallet network. Please note that there is no tracking reference provided for pallet deliveries and they are kerbside delivery service only meaning that the delivery driver will not bring your item(s) inside your home. Read our article on pallet deliveriesfor more information.
At RPM Power, customer satisfaction is our highest priority. We are committed to supporting you with any product-related concerns that may arise. While it is inevitable that issues may occasionally occur, our warranty policy is designed with a customer-focused approach to ensure a fair and efficient resolution.
All RPM Power products are covered under warranty. Warranty coverage varies depending on product type. For full details, please read our Warranties Terms and Conditions.
New
Elite Extender Arms
€469.99–€639.99Price range: €469.99 through €639.99
Open the arms outward for wide crossover-style cable spacing, or converge them inward for a central 1:1 dual-stack route. Horizontal width and vertical height lock independently once set.
Open outward
Create Crossover-Width Cable Spacing
Sweep the arms left and right to open the pulley positions outward for wider cable paths and crossover-style training angles. Each extended arm adds 34cm of width on its own side of the rack.
Converge inward
Use Both Stacks in 1:1
Swing both arms inward to create a central 1:1 dual-stack route for low rows and lat pulldowns, making twice the single-stack capacity available through one attachment path.
75mmUpright compatibility
17mmHole compatibility
Designed as an upgrade path
Choose the Correct Extender Setup for Your Rack
+EXTENDER COMPATIBLE
B: Extender Arm only
Use the four-bolt swap-over interface. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A new cable is required for most existing conversions, unless a suitable spare cable can be adjusted.
CHECK COMPATIBILITY BEFORE ORDERING: This attachment has different component and cable requirements depending on the host rack. Review the Detailed Description before ordering. If you are unsure, contact RPM with your rack model and current cable setup so the correct configuration can be confirmed.
RPM Power Designed Pulley Extender Arm Attachment
Set Cable Height, Width and Direction Around the Station
After installation, use the vertical adjuster to raise or lower the arm and the horizontal adjuster to sweep through 180 degrees, opening outward for crossover-width spacing or converging inward for central cable paths. Horizontal width and vertical height lock independently once set. Each pulley rotates through 360 degrees to follow the selected line.
3Horizontal arm adjustment, independently lockable
360°Pulley rotation follows the cable line
Two cable modes in one system
Converge the Arms, Use Both Stacks in 1:1
Angle both arms inward to create a central 1:1 dual-stack route, doubling the available single-stack capacity for low rows and lat pulldowns.
STANDARD 2:1
Independent Cable Paths
On a compatible host cable system, use each arm independently with a single stack assigned to its chosen cable path.
CONVERGED 1:1
Central Dual-Stack Path
Bring both stacks together for rows, pulldowns and other central high-capacity cable movements.
Installation setting plus three live adjustments: Set the mounting-hole position once during installation to match the rack cable route. Thereafter, adjust vertical height, horizontal cable width and pulley rotation for the required training position.
Multi-position mounting
Designed for RPM’s Known Overhanging Pulley Paths
Developed in house by RPM Power for known RPM cable-path layouts, this is an installation setting rather than a training-time adjustment. Select the fixing position once around the overhanging pulley route used by the rack configuration so the arm and pulley sit in the intended cable line.
Multiple fixing positions: position the arm for the overhanging pulley route used by the rack.
ODIN rack path
Right and Left Upright-Side Top Pulleys
ODIN uses top-pulley paths to the right and left of the uprights. The fixing positions let the arm be placed to match those side cable routes.
Apex rack path
Central Upright Cable Path
Apex uses a central upright cable route. The arm can be fixed in the position that aligns with this central overhanging pulley placement.
Designed for every rack generation
A Clear Upgrade Path for Existing and Future Racks
The extender system is designed so both existing and future RPM rack owners can upgrade. Extender Compatible racks use a direct four-bolt swap-over route. Existing and non-compatible racks can also upgrade, but may require additional hardware and cable depending on the configuration already in place.
Component key: A is the upright dolly. B is the extender arm.
+EXTENDER COMPATIBLE
B: Extender Arm only
Remove the four bolts from the standard pulley dolly and attach the B extender arm in the same mounting position. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A cable change is required for most existing conversions. A suitable spare cable may be adjusted instead. The total upgrade cost therefore depends on the hardware and cable already in place.
+View cable and upright-dolly requirements
Existing standard-dolly installations require a cable change when converting to extender arms. Order a new cable alongside the arms where required. We can cut and supply the cable to the required length. Older stock and non-RPM rack conversions also require the A upright dolly.
From Q3 2026, new RPM 75mm x 75mm racks marked Extender Compatible will be supplied with sufficient cable for the standard pulley dolly or B extender arm when the selected configuration is specified at purchase.
Selection
Extender Arm Only, Upright Dolly + Extender Arm
Specifications
Specification
Details
Product
RPM Power Extender Arms
Arm Length
637mm
Arm Width
227mm
Net Weight
21kg
Gross Weight
25kg
Package A
34 × 22 × 25cm
Package B
50 × 31 × 24cm
Training Style
Strength, Hypertrophy, Functional & Athletic Training
The daily cut-off times for orders dispatched from RPM Power is 12pm. We aim to dispatch orders within the time frames outlined on ourShipping & Deliveries page. All times are measured in business days only and exclude weekends and Republic of Ireland public holidays.
Dispatch and delivery timeframes should be considered as estimates and are not guaranteed. These can vary during peak seasons and end-of-sale periods. We will draw your attention to any dispatch delays that may be occurring during these periods with a notice on our website.
Parcel orders: Small/lightweight items are dispatched via the courier network and automated tracking details will be provided to you. To ensure minimal shipping costs for our customers, some items may arrive in multiple packages. Although dispatched together, these packages can often become separated on their way to you and some may arrive a day later than the others.
Pallet orders: Heavy/oversized items are dispatched via the pallet network. Please note that there is no tracking reference provided for pallet deliveries and they are kerbside delivery service only meaning that the delivery driver will not bring your item(s) inside your home. Read our article on pallet deliveriesfor more information.
At RPM Power, customer satisfaction is our highest priority. We are committed to supporting you with any product-related concerns that may arise. While it is inevitable that issues may occasionally occur, our warranty policy is designed with a customer-focused approach to ensure a fair and efficient resolution.
All RPM Power products are covered under warranty. Warranty coverage varies depending on product type. For full details, please read our Warranties Terms and Conditions.
Open the arms outward for wide crossover-style cable spacing, or converge them inward for a central 1:1 dual-stack route. Horizontal width and vertical height lock independently once set.
Open outward
Create Crossover-Width Cable Spacing
Sweep the arms left and right to open the pulley positions outward for wider cable paths and crossover-style training angles. Each extended arm adds 34cm of width on its own side of the rack.
Converge inward
Use Both Stacks in 1:1
Swing both arms inward to create a central 1:1 dual-stack route for low rows and lat pulldowns, making twice the single-stack capacity available through one attachment path.
75mmUpright compatibility
17mmHole compatibility
Designed as an upgrade path
Choose the Correct Extender Setup for Your Rack
+EXTENDER COMPATIBLE
B: Extender Arm only
Use the four-bolt swap-over interface. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A new cable is required for most existing conversions, unless a suitable spare cable can be adjusted.
CHECK COMPATIBILITY BEFORE ORDERING: This attachment has different component and cable requirements depending on the host rack. Review the Detailed Description before ordering. If you are unsure, contact RPM with your rack model and current cable setup so the correct configuration can be confirmed.
Set Cable Height, Width and Direction Around the Station
After installation, use the vertical adjuster to raise or lower the arm and the horizontal adjuster to sweep through 180 degrees, opening outward for crossover-width spacing or converging inward for central cable paths. Horizontal width and vertical height lock independently once set. Each pulley rotates through 360 degrees to follow the selected line.
3Horizontal arm adjustment, independently lockable
360°Pulley rotation follows the cable line
Two cable modes in one system
Converge the Arms, Use Both Stacks in 1:1
Angle both arms inward to create a central 1:1 dual-stack route, doubling the available single-stack capacity for low rows and lat pulldowns.
STANDARD 2:1
Independent Cable Paths
On a compatible host cable system, use each arm independently with a single stack assigned to its chosen cable path.
CONVERGED 1:1
Central Dual-Stack Path
Bring both stacks together for rows, pulldowns and other central high-capacity cable movements.
Installation setting plus three live adjustments: Set the mounting-hole position once during installation to match the rack cable route. Thereafter, adjust vertical height, horizontal cable width and pulley rotation for the required training position.
Multi-position mounting
Designed for RPM’s Known Overhanging Pulley Paths
Developed in house by RPM Power for known RPM cable-path layouts, this is an installation setting rather than a training-time adjustment. Select the fixing position once around the overhanging pulley route used by the rack configuration so the arm and pulley sit in the intended cable line.
Multiple fixing positions: position the arm for the overhanging pulley route used by the rack.
ODIN rack path
Right and Left Upright-Side Top Pulleys
ODIN uses top-pulley paths to the right and left of the uprights. The fixing positions let the arm be placed to match those side cable routes.
Apex rack path
Central Upright Cable Path
Apex uses a central upright cable route. The arm can be fixed in the position that aligns with this central overhanging pulley placement.
Designed for every rack generation
A Clear Upgrade Path for Existing and Future Racks
The extender system is designed so both existing and future RPM rack owners can upgrade. Extender Compatible racks use a direct four-bolt swap-over route. Existing and non-compatible racks can also upgrade, but may require additional hardware and cable depending on the configuration already in place.
Component key: A is the upright dolly. B is the extender arm.
+EXTENDER COMPATIBLE
B: Extender Arm only
Remove the four bolts from the standard pulley dolly and attach the B extender arm in the same mounting position. No new cable or upright dolly is required.
Existing or non-compatible rack
A: Upright Dolly + B: Extender Arm
A cable change is required for most existing conversions. A suitable spare cable may be adjusted instead. The total upgrade cost therefore depends on the hardware and cable already in place.
+View cable and upright-dolly requirements
Existing standard-dolly installations require a cable change when converting to extender arms. Order a new cable alongside the arms where required. We can cut and supply the cable to the required length. Older stock and non-RPM rack conversions also require the A upright dolly.
From Q3 2026, new RPM 75mm x 75mm racks marked Extender Compatible will be supplied with sufficient cable for the standard pulley dolly or B extender arm when the selected configuration is specified at purchase.
The daily cut-off times for orders dispatched from RPM Power is 12pm. We aim to dispatch orders within the time frames outlined on ourShipping & Deliveries page. All times are measured in business days only and exclude weekends and Republic of Ireland public holidays.
Dispatch and delivery timeframes should be considered as estimates and are not guaranteed. These can vary during peak seasons and end-of-sale periods. We will draw your attention to any dispatch delays that may be occurring during these periods with a notice on our website.
Parcel orders: Small/lightweight items are dispatched via the courier network and automated tracking details will be provided to you. To ensure minimal shipping costs for our customers, some items may arrive in multiple packages. Although dispatched together, these packages can often become separated on their way to you and some may arrive a day later than the others.
Pallet orders: Heavy/oversized items are dispatched via the pallet network. Please note that there is no tracking reference provided for pallet deliveries and they are kerbside delivery service only meaning that the delivery driver will not bring your item(s) inside your home. Read our article on pallet deliveriesfor more information.
At RPM Power, customer satisfaction is our highest priority. We are committed to supporting you with any product-related concerns that may arise. While it is inevitable that issues may occasionally occur, our warranty policy is designed with a customer-focused approach to ensure a fair and efficient resolution.
All RPM Power products are covered under warranty. Warranty coverage varies depending on product type. For full details, please read our Warranties Terms and Conditions.
Our customers love us!
Our customers love us!
Filter by
Price
€€
Category Type
Height (cm)
Width (cm)
Length (cm)
Range
Recommended Use
Colour
PREMIER EXPRESS SHIPPING
Get Your Order Delivered Fast!
Looking for faster delivery? With Premier Shipping by RPM Power, you can receive select items within 24 working hours in Ireland & 48 Hours in UK via DHL Express. This premium service is ideal for customers who need their order quickly and want the peace of mind of tracked express delivery.
Premier Shipping is available for eligible items under 30kg. While our standard shipping (via GLS) typically delivers within 2–4 working days, Premier Shipping ensures priority dispatch and express delivery.
Please note:
Premier Shipping is available only on select products.
In the United Kingdom, there are two DHL Premier Shipping options available: Premier Shipping Express and Premier Shipping Economy. The main difference is the delivery timeframe. Premier Shipping Economy typically delivers within 2–4 working days, while Premier Shipping Express delivers faster, usually within 1–2 working days.
RPM Power reserves the right to cancel or adjust any order where the DHL shipping cost significantly exceeds anticipated rates due to size, weight, or delivery location.
Orders must be placed before [11.15am] to qualify for next-day delivery.
Premier Delivery only counts for orders placed on weekdays. If, for example you order on a Saturday or Friday afternoon, the order will not be dispatched until Monday.
RPM Power is not liable for any damages that occur during DHL’s transit. For full details on DHL’s service terms, please refer to their Terms & Conditions.
Premier Shipping only qualifies on workdays (Monday - Friday), orders placed on Saturday or Sunday will be dispatched on Monday.
PREMIER EXPRESS SHIPPING DETAILS
Urgent, Time Sensitive Parcels
Next Possible Business Day / 2 Days to Mainland UK
Delivered on Next Possible Day
12:00PM
Available Countries
Ireland, Great Britain, France, Germany, and Luxembourg
Register now and get 100% FREE access to RPM Care, special offers, pre-order preference notifications, updates, exercises and nutrition tips, and so much more!👇
